Troubleshooting Network Connection Problems

Depending on how elaborate they are, home networks can be complicated. Unfortunately, because of this complexity, problems occasionally happen. Fortunately, you can usually solve these problems yourself. In most cases, finding the problem is a matter of going through a series of steps to eliminate potential issues one by one until you find the source of the problem. This article walks you through isolating your problem, troubleshooting the problem, and, if necessary, contacting the right organization for support.

If you are setting up your home network for the first time, refer to Set up a wired network or Set up a wireless network. The guidance in this article assumes that you were previously able to use your network, although the information here might be useful for troubleshooting setup problems, too.

How to isolate networking problems

People who work with networks think of them in terms of layers. These layers include the Internet, your modem and router, and the computer (or computers) on your network. To troubleshoot a problem effectively, you must first identify which network layer is causing the problem. The following diagram shows the different layers that might be the cause of a problem.

Windows XP says your network adapter has limited or no connectivity

If Windows XP says your network adapter has limited or no connectivity, it could be due to several different problems, including a failed Internet connection, a misconfigured router, or a misconfigured network adapter. Follow these steps to troubleshoot the problem. (You can stop following the steps if your network connection starts to work.)

1. In the Network Connections window, right-click your network adapter, and then click Repair. For detailed instructions, read Repairing network connections.

2. Unplug your modem. If you are unsure which device might be your modem, it is the device that is connected directly to your phone line (if you have DSL) or cable connection (if you have a cable modem). Wait one minute, and then plug your modem back in again.

3. If you have a router connected to your modem, unplug it. If you are unsure which device might be your router, look for the device that has at least two network cables: one that connects to your modem; and another that connects to your computer. You may also have a wireless router, which would be connected to your modem and would have one or more antennas. Wait one minute, and then plug your router back in again.

4. Restart your computer.

5. If your network adapter still shows "Limited or no connectivity" and you have customized your router's configuration, verify that the router has DHCP (Dynamic Host Configuration Protocol) enabled. Enable DHCP, and then restart your computer. DHCP automatically assigns an Internet Protocol (IP) address to your computer, which uniquely identifies your computer on your network. For instructions on how to enable DHCP for your router, refer to your router's documentation.

6. If you are using a router, unplug the network cable that connects your modem to your router, and connect your computer directly to your modem. Then restart your computer. If your computer connects properly after restarting, the problem is with your router. Contact your router manufacturer for support.

7. If your network adapter still indicates "Limited or no connectivity" when your computer is connected directly to your modem, contact your Internet service provider (ISP) for support. To speed up the troubleshooting process, describe the steps you have already taken, including restarting your modem, router, and computer, and connecting your computer directly to your modem. The "Limited or no connectivity" error message indicates that your computer is properly connected to your home network; however, the ISP's DHCP server is not assigning it an IP address. This problem could be caused by a failed DHCP server on the ISP's network, a failed modem, or a problem with your Internet connection. Alternatively, the ISP may require you to use a "static" IP address, which only its support staff can help you configure.

After following these steps, you should have identified the problem as your router, your modem, or your Internet connection, and then either reconfigured or repaired the failed component.

Windows XP says your network adapter is connected, but you can't reach the Internet

If you reached this section, your computer is probably connected to your home network properly, but there is a failure with your router, modem, or Internet connection. In this case:

1. First, verify that you can't reach the Internet. Start Microsoft Internet Explorer, and attempt to connect to the following Web sites: http://www.microsoft.com, http://www.msn.com, and http://www.windowsmarketplace.com. If any of the Web sites open correctly, your Internet connection is functioning properly. If all of the Web sites fail to open, continue following these steps.

2. Unplug your modem. If you are unsure which device might be your modem, it is the device that is connected directly to your phone line (if you have DSL) or cable connection (if you have a cable modem). Wait one minute, and then plug your modem back in again.

3. If you have a router connected to your modem, unplug it. If you are unsure which device might be your router, look for the device that is connected directly to your modem. Wait one minute, and then plug your router back in again.

4. Restart your computer.

5. If you have more than one computer on your network, turn the other computers off. Also, close any network applications that you might have open, including file sharing and peer-to-peer applications. These applications can consume so much bandwidth that they might prevent you from being able to browse the Web. Repeat step 1 to retest your Internet connection. If the connection works now, the problem is that one of your applications is consuming too much of your Internet bandwidth or attempting to connect to too many different computers. Close the application, or configure it to use less bandwidth or fewer connections.

6. If you have previously configured your computer with a static IP address (for example, to connect to your office network), you probably need an automatic IP address at home. Fortunately, you can configure Windows XP to use both by following the steps in Automatic configuration for multiple networks.

7. If you are using a router, unplug the network cable that connects your modem to your router, and connect your computer directly to your modem. Then restart your computer. If your computer connects properly after restarting, the problem is with your router. Contact your router manufacturer for support.

8. If possible, connect a different computer to your modem, and attempt to access the Internet. If the computer is able to access the Internet, you might have a problem with your Web browser. Contact your computer manufacturer for support.

9. Your modem or your Internet connection has failed. To resolve the problem, contact your ISP technical support. To speed up the troubleshooting process, describe the steps you have already taken, including restarting your modem, router, and computer, and connecting your computer directly to your modem.

After following these steps, you should have identified the problem as your router, modem, Internet connection, or Web browser, and then either reconfigured or repaired the failed component.

Read more: http://www.articlesbase.com/networks-articles/troubleshooting-network-connection-problems-3466051.html